1
Maintenance, Servicing, and Mechanical issues / Re: Correct size bolts in fairings
« Last post by Jayjay75 on Today at 09:16:43 pm »Fantastic thanks both 👍🏻
30 Sep 23, 21:29 pm
|
2
Maintenance, Servicing, and Mechanical issues / Re: Correct size bolts in fairings« Last post by Sidewinder on Today at 09:10:34 pm »Shortest ones fit things to the tank, that's the most important bit to remember.
3
Maintenance, Servicing, and Mechanical issues / Re: Correct size bolts in fairings« Last post by gosling 1 on Today at 08:14:45 pm »Have a look at the OEM parts diagrams at fowlersparts.co.uk , the descriptions usually give the bolt sizes and even color.
4
Tyres and Wheels / Re: Michelin Pilot Road 6 GT or not GT ?« Last post by Yellow Dog on Today at 08:08:06 pm » Originally Posted by Mike_B ![[+]](https://www.tiger1050.com/vbicons/viewpostright.png "View Post") Thanks Mike. I found the right sizes at http://www.thevisorshop.com. Great pricing too  5
Maintenance, Servicing, and Mechanical issues / Re: The End Of The Road or a new beginning . . . . . .« Last post by Javaman on Today at 07:29:50 pm »A little more prep today in readiness for removing the radiator and exhaust tomorrow . . . Only managed to drain the coolant.
Again, the manual is silly - it suggests the first step is to remove the radiator cap and collect the fluid which drains out, before loosening the radiator bleed screw and then removing the bleed bolt in the block. Doing it this way will result in coolant everywhere - the first step alone will empty the expansion tank all down the radiator - just daft. Anyway, having changed the coolant in the bike previously, it’s a very easy job and especially with a slightly modified technique 1. Remove the single mounting bolt from the expansion tank and with its hoses still attached, invert the tank and empty its contents before resecuring in place. 2. Remove the drain screw in the block - no coolant will be released. 3. Place a hose over the hole, tie it in position and place the free end in a receiving container with a capacity of 3 litres or more (you will be collecting +\- 2 litres of coolant 4. Undo and remove the radiator bleed screw in the top right surface of the radiator. This will allow about 1.4litres of coolant to flow out of the block via the hose and without spilling a drop. 5. Release the lower hose from the water pump as per the manual. Be aware that this will suddenly release almost a pint of coolant and without care, it will spray out everywhere. Best best is to wiggle the hose towards he end of the spigot and when it starts to dribble, simply leave it to drip slowly whilst you go and make a coffee. When drained, the last dregs can be drained by fully removing the hose - job done I keep my coolant on “max” when cold and draining the engine this way produced exactly 2.00 litres of coolant. I will use this figure as a means of knowing whether or not I have any air locks when refilling, as I should be able to refill with this amount to bring it back to “max”.     6
Maintenance, Servicing, and Mechanical issues / Correct size bolts in fairings« Last post by Jayjay75 on Today at 06:30:36 pm »Hi I rather stupidly removed all fairings and tried to rely on my cabbage brain and now can’t recall which length bolts go in the correct hole for the fairings. I’ve tried Haynes manual but that’s not listed.
Does anyone happen to know which length fits which hole? There’s short stubby ones, longer length and one that’s slightly longer again. Thanks 7
Maintenance, Servicing, and Mechanical issues / Re: Starting issue at the first start of the day« Last post by Scrapiron on Today at 05:48:24 pm »I have a NOCO Lithium NLP14 battery installed with upgraded battery cables. Will look into the V2 tune. Thanks
8
Tyres and Wheels / Re: Michelin Pilot Road 6 GT or not GT ?« Last post by Mike_B on Today at 04:48:51 pm »Originally Posted by Yellow Dog It’s definitely made in 180 width. I usually get tyres from FWR in south London - they are showing 5 of that size in stock. 9
Maintenance, Servicing, and Mechanical issues / Re: ECU toast or something simple?« Last post by TrueType on Today at 11:59:22 am »Originally Posted by Sidewinder Yes I had tried with the spare key. Not luck unfortunately. 10
Maintenance, Servicing, and Mechanical issues / Re: ECU toast or something simple?« Last post by Sidewinder on Today at 11:26:57 am »Another thing that will stop you is the integrated immobiliser. The transponder in the key getting signal from the aerial in the lock unit. If the proper signal is not sent/rec'd it won't start. Have you tried spare key?
Needs be no magnets, no other transponder equipped keys etc. |