Author Topic: o2 sensor  (Read 1139 times)

0 Members and 1 Guest are viewing this topic.

Offline JLW

  • Tiger Member
  • **
  • Topic Author
  • Posts: 18
  • Bike/Model: Tiger 1050 [2007]
  • City / Town: Retford
  • Country: gb
o2 sensor
on: 10 August, 2021, 06:39:26 PM
Hi,
I`ve got a replacement o2 sensor for my tiger 1050 2007, as last one disintegrated  :003: and wondered how the cable from the o2 sensor is routed back to the connector block?
Any pictures would be a great help
Many thanks,
Jae

#1

Offline Sidewinder

  • Tiger Master
  • ****
  • Posts: 852
  • Bike/Model: 2007 Tiger 1050 Yellow
  • City / Town: Sheffield
  • Country: gb
Re: o2 sensor
Reply #1 on: 10 August, 2021, 07:54:29 PM
Mine goes rearwards, right side of sump and filter, then in a little clip then up between the back of the engine and cross frame member.  Then I dunno cos bike in garage and i can't see where from there.

#2

Offline JLW

  • Tiger Member
  • **
  • Topic Author
  • Posts: 18
  • Bike/Model: Tiger 1050 [2007]
  • City / Town: Retford
  • Country: gb
Re: o2 sensor
Reply #2 on: 11 August, 2021, 10:22:57 AM
 cheers

like this?





#3

Offline Sidewinder

  • Tiger Master
  • ****
  • Posts: 852
  • Bike/Model: 2007 Tiger 1050 Yellow
  • City / Town: Sheffield
  • Country: gb
Re: o2 sensor
Reply #3 on: 11 August, 2021, 11:38:30 AM
Underneath pic yeah.  The 2nd pic, no, the wire is run/connected in the space between the frame, see that big engine frame bolt in your pic?  The other end of that is in like a space above the rear of gearbox and my connector is there.  The loom runs across the top of that space and has a branch off it with the o2 plug on.  If I look thru above the chain in front of where the shock is, rear wall of engine you can see the plug.

#4

Offline JLW

  • Tiger Member
  • **
  • Topic Author
  • Posts: 18
  • Bike/Model: Tiger 1050 [2007]
  • City / Town: Retford
  • Country: gb
Re: o2 sensor
Reply #4 on: 12 August, 2021, 01:17:38 PM
Blimey,
Ok do I need to take tank off to do that?
Cheers
J

#5

Offline Sidewinder

  • Tiger Master
  • ****
  • Posts: 852
  • Bike/Model: 2007 Tiger 1050 Yellow
  • City / Town: Sheffield
  • Country: gb
Re: o2 sensor
Reply #5 on: 12 August, 2021, 01:39:52 PM
No, it's further back than where the tank is.  Essentially you want it where it is in your pic but inside of the frame.  With bike on centre stand to put swingarm lowest I can reach a hand either side of the shock to unplug mine.

#6

Offline JLW

  • Tiger Member
  • **
  • Topic Author
  • Posts: 18
  • Bike/Model: Tiger 1050 [2007]
  • City / Town: Retford
  • Country: gb
Re: o2 sensor
Reply #6 on: 13 August, 2021, 01:09:51 PM
cheers for this, will give it a go later today  :002:

#7

Offline JLW

  • Tiger Member
  • **
  • Topic Author
  • Posts: 18
  • Bike/Model: Tiger 1050 [2007]
  • City / Town: Retford
  • Country: gb
Re: o2 sensor
Reply #7 on: 16 August, 2021, 08:37:31 AM

Wish I had replaced it earlier... its a different bike now, well smooth  :028:

#8

Offline indytiger1050

  • Tiger Supporter
  • Supreme Tiger
  • *
  • Posts: 22233
  • Bike/Model: 79 Honda 750L
  • City / Town: Indianapolis
  • Country: us
Re: o2 sensor
Reply #8 on: 17 August, 2021, 01:23:03 AM
 :046: :152:
Support the forum.   :031:

 



reconstruction